2012 Jeep Wrangler Drive Shaft Parts

Unlimited Sahara 3.6L V6 change vehicle

Choose your Transmission for your 2012 Jeep Wrangler Unlimited Sahara 3.6L V6

Showing 1 - 5 of 5 products

Sort:

Show:

Image

SKU

Product

Rating

Price

36.50 in. Long RE1810 Adapter Required For Installation~Sold Separately~Req. PN[RE1883-365] For 07-11 Models w/Automatic Trans~Req. PN[RE1883-365] For Models 07-17 w/Manual Trans
CV Style Drive Shaft; Front; 36.50 in. Long;
CV Style Drive Shaft
Product Attributes:
- Usage: Oem
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov.
- Horsepower Rating: Oem
Features:
- Compatible With RE1811 Slip Yoke Eliminator Kit
- Compatible With Atlas Transfer Cases
- Compatible With Any 1310 Series CV Yoke
- Measured Center To Center On Joint
- Measured With Slip Stub At Center Of Travel
- Measure w/Vehicle On Ground In Running Position
Spicer Drive Shafts And Components Are As Good As They Get. This Drive Shaft Is Compatible With Atlas Transfer Cases And Any Other 1310 Series CV Yoke. Measurements Are Taken Center To Center On The U-Joint With The Slip Stub At The Center Of Its Travel. Measure Your Vehicle On The Ground In The Running Position To Get Correct Length.

Additional Fitment Information:

Vehicle	Transmission	Position	Sub Model
2012 - Jeep Wrangler	Manual	Front	Unlimited Sahara

9 In Stock

$1,025.87 CAD

$1,231.04 CAD

OEM Product: This Original Equipment Manufacturer part is the same part that was made & installed by the car manufacturer at the factory where the car was produced.
with Dana 186mm Axle

Additional Fitment Information:

Vehicle	Transmission	Position
2012 - Jeep Wrangler	Automatic	Front

Front And For Vehicles w/3.5 in or Greater Lift Height
Driveshaft Kit; Front And Rear; For Vehicles w/3.5 in or Greater Lift Height;
Driveshaft Kit
Product Attributes:
- Usage: Oem
- WARNING CA Proposition 65: Yes
- WARNING CA Proposition 65 Message: Warning: Cancer And Reproductive Harm - Www.p65warnings.ca.gov.
- Horsepower Rating: Oem
Features:
- Driveshaft Kit
Prevent Driveline Vibration After You Lift Your Jeep JK w. Our Dana Spicer 1310 CV Style JK Driveshafts. Designed To Replace The Factory Shafts And To Be Ran w. Our Replacement Yoke And Flange For The Transfer Case. Built For Daily Driving And The Demands Of Off Roading. Driveshaft Lengths Are For Factory Gasoline Motors.

Additional Fitment Information:

Vehicle	Sub Model
2012 - Jeep Wrangler	Unlimited Sahara

For 3.5-6 in. Short Arm Lift Kits; For 2.5-6 in. Long Arm Lift Kits; Includes Flanges; Yokes; Hardware; Collapsed Length 41.25 in.; Extended Length 44.75 in. Install Time 2-3 Hours
CV Drive Shaft; Rear; For 3.5-6 in. Short Arm Lift Kits; For 2.5-6 in. Long Arm Lift Kits; Includes Flanges; Yokes; Hardware; Collapsed Length 41.25 in.; Extended Length 44.75 in.;
CV Drive Shaft
Product Attributes:
- Usage: Oem
- WARNING CA Proposition 65: No
- Horsepower Rating: Oem
Features:
- Collapsed Length: 41.25 in.
- Extended Length: 44.75 in.
- Good Choice To Eliminate Vibration Issues
- Includes Brute Force Red Seals
- Includes Better Quality CV Joints
- Shaft Strength Is Twice As Strong As The Factory Drive Shaft
- Grease Fittings Are Out Of Way Of The Transmission Oil Pan
This double cardan style CV driveshaft is necessary for Jeep JK models equipped with 3.5in - 6in short arm suspension lifts or 2.5in - 6in long arm suspension lifts. It features a replacement flange for the differential pinions as opposed to using an adapter flange. These flanges are machined from solid billet steel. They are designed to accept standard in.off the shelf in. mating flanges. If these flanges ever break, you at least stand a chance of getting a replacement part from almost any drive line shop. This also nets a longer drive shaft with the center of the universal joint closer to the pinion bearing.

Additional Fitment Information:

Vehicle	Position	Sub Model
2012 - Jeep Wrangler	Rear	Unlimited Sahara

For 3.5-6 in. Short Arm Lift Kits; For 2.5-6 in. Long Arm Lift Kits; Includes Flanges; Yokes; Hardware; Fits Dana 30 and Dana 44 Front Axles Install Time 2-3 Hours
CV Drive Shaft; Front; For 3.5-6 in. Short Arm Lift Kits; For 2.5-6 in. Long Arm Lift Kits; Includes Flanges; Yokes; Hardware; Fits Dana 30 and Dana 44 Front Axles;
CV Drive Shaft
Product Attributes:
- Usage: Off-road
- WARNING CA Proposition 65: No
- Horsepower Rating: Oem
Features:
- 10-Stage Variable Valving
- High Pressure Nitrogen Charged
- Eliminates Contact Between The Stock Drive Shaft And Oil Pan
- On Automatic Transmission Models
- Good Choice To Eliminate Vibration Issues
- Includes Brute Force Red Seals
- Includes Better Quality CV Joints
- Shaft Strength Is Twice As Strong As The Factory Drive Shaft
- Grease Fittings Are Out Of Way Of The Transmission Oil Pan
This double cardan style CV driveshaft is necessary for Jeep JK models equipped with 3.5in - 6in short arm suspension lifts or 2.5in - 6in long arm suspension lifts. It features a replacement flange for the differential pinions as opposed to using an adapter flange. These flanges are machined from solid billet steel. They are designed to accept standard in.off the shelf in. mating flanges. If these flanges ever break, you at least stand a chance of getting a replacement part from almost any drive line shop. This also nets a longer drive shaft with the center of the universal joint closer to the pinion bearing.